How to Work Safely with - Hazardous Products Using the "Flame" Pictogram

The symbol within the pictogram is a flame with a line underneath it. This symbol indicates that hazardous products with this pictogram can ignite easily and burn rapidly if they are not stored and handled properly.

In most workplaces, you will see this pictogram used on hazardous products for the following hazard classes:

• Flammable gases – Category 1
• Flammable aerosols – Category 1 and Category 2
• Flammable liquids – Category 1, Category 2 and Category 3
• Flammable solids – Category 1 and Category 2

There are other hazard classes that use the flame pictogram but products with these hazards are not commonly found in workplaces:

• Self-reactive substances and mixtures - Type B*, Type C, Type D, Type E and Type F
• Pyrophoric liquids – Category 1
• Pyrophoric solids – Category 1
• Pyrophoric gases – Category 1
• Self-heating substances and mixtures – Category 1 and Category 2
• Substances and mixtures which, in contact with water, emit flammable gases – Category 1, Category 2 and Category 3
• Organic peroxides – Type B*, Type C, Type D, Type E and Type F

*Note that the most severe hazard category in the self-reactive substances and mixtures hazard class (Type A) is assigned the exploding bomb pictogram. Type B is assigned two pictograms – the flame and the exploding bomb.

Hazardous products with the flame pictogram can be a fire or explosion hazard in the workplace.

For a fire to occur, three elements must be together at the same time and in the right proportions:

• a source of fuel (e.g., the flammable product),
• oxygen, and
• heat (e.g., an ignition source such as a spark).

It is very important when working with flammable products that these three elements are not present together in the right amounts at any time.

The following hazards are also associated with flammable liquids:

• Accumulation of static charge – static electricity is the electric charge generated when there is friction between two things made of different materials or substances. This charge can occur and accumulate when flammable liquids are poured, pumped, filtered, agitated, stirred or flow through pipes, and these actions can act as an ignition source. Release of the static charge from the liquid can ignite flammable products.
• Flashback – the vapour of most flammable liquids is heavier than air. In this case, the vapour can spread a long distance along the ground or floor and eventually be ignited by a distant spark, flame or other source of heat. Once the vapour ignites, the flames or fire can “flash-back”, meaning that the flames travel back to the container or source of the flammable liquid and an explosion can occur.

You also need to consider the potential for hazardous thermal decomposition and combustion products. When flammable products burn, hazardous gases and vapours can be produced (e.g., carbon monoxide, hydrogen cyanide and nitrogen oxides).

The WHMIS 2015 signal words and hazard statements for flammable gases, aerosols, liquids and solids are:

Below are the signal words and hazard statements for the other WHMIS 2015 hazard classes and categories that are assigned the flame pictogram.

*Recall that these hazard classes and categories are also assigned the explosion pictogram.

Fire and explosion are the main concerns, but other hazards may be present. Supervisors and workers must understand the specifics of what all of the hazards of the product are and how to use it safely.

Other hazards include:

• Health hazards such as acute toxicity, skin corrosion or irritation, carcinogenicity or reproductive toxicity.
• Other physical hazards – such as reactivity or corrosive to metals.

ALWAYS check the SDS and label for the product that you are working with to ensure that you know what is being used and all of the hazards and precautions associated with the product. Ask questions if you are not sure.

• ALWAYS Check the Safety Data Sheet (SDS) for information about ALL of the hazards and the necessary precautions for the product being used. Ask questions if you are not sure.
• If it is not possible to eliminate use of the hazardous product in your workplace, evaluate whether it is possible to substitute it with a less hazardous product.
• Prevent the release of flammable products into the air.
• Use only in well-ventilated areas. Keep container tightly closed.
• Use the smallest amount necessary for the job.
• Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking.
• Make sure that there is no hot work done in the area, or hidden sources of ignition (e.g., pilot lights in a furnace or hot water tank).
• For aerosols, do not spray on an open flame or other ignition source. Do not pierce or burn, even after use.
• Remove combustible materials (e.g., oily rags, cardboard boxes) from the area where these products are used. Dispose of combustible material appropriately (e.g., oily rags are in approved containers).
• For volatile flammable liquids:
  • Use non-sparking tools
  • Use explosion-proof electrical, ventilating and lighting equipment.
  • Take action to prevent static discharges.
• Sometimes it is necessary to ground and bond container and receiving equipment. Be sure that you understand when and how to do this properly.
• Wear protective gloves, protective clothing, eye protection and/or face protection, as required.
• If personal protective equipment (PPE) is required, the employer must make sure that workers are thoroughly trained in its selection, fit, use and maintenance. Refer to the SDS for guidance on selection.
• For self-reactives and organic peroxides, keep only in original packaging, and keep cool.
• Handle and store pyrophoric products and products that react with water to release a flammable gas under inert gas or a liquid/gas specified by the supplier. Protect from moisture.
• Keep self-heating products cool.
• Avoid contact with incompatible products.
• Be aware of specific conditions to avoid, e.g., air, water, moisture, temperature, pressure, friction, sunlight. Check the SDS for specific information and recommendations.
• Avoid spilling the product and contaminating your skin or clothing.
• Do not weld, cut or perform hot work on empty container until all traces of product have been removed.
• Immediately report leaks, spills or failures of safety equipment (e.g., the ventilation system) to your supervisor.
• Keep work areas clean and tidy. Wipe up spills and keep surfaces clean to prevent contact with skin or incompatibles. Prevent accumulation of dust or other residues on ledges or other surfaces.

• Use equipment designed for flammable storage such as flammable storage fridge, flammable cabinets, or flammable safety cans.
• Avoid storing large quantities if possible.
• Post warning signs.
• Inspect containers and storage area regularly for signs of leakage or damage. Contain spills or leaks by storing in trays made from compatible materials.
• Store in a well-ventilated place
• Keep cool.
• Protect aerosols and organic peroxides from sunlight.
• Do not expose aerosols to temperatures exceeding 50 deg C (122 deg F).
• Store organic peroxides, self-reactive products and self-heating products within the temperature range recommended by the supplier. Store separately.
• Maintain air gap between stacks or pallets of self-heating products.
• Store products that react with water in a dry place and in closed containers.
• Keep away from incompatible materials. Check SDS for incompatibles.
• Ensure that appropriate fire-fighting and spill clean-up equipment is readily available.
• Avoid storing flammable products in basements. Ground floor storage is preferred because it provides easier access for emergency situations.
• Follow all applicable health and safety regulations, fire and building codes.

Understand and practice emergency procedures so that you know what to do if it becomes necessary to act:

• Make sure that appropriate fire extinguishers are available.
• Be aware of at least two different exit paths in the event of fire.
• Make sure that eyewash and emergency shower are readily available in the immediate work area. These devices must be tested regularly.
• Have spill control procedures and equipment ready (e.g., absorbent spill control materials, PPE, non- sparking tools, etc.). Avoid using combustible materials (such as paper towels or sawdust) to clean up or absorb spills.
• Remove contaminated clothing and leather shoes or boots since they can be a severe fire hazard. Wash contaminated items, immediately and thoroughly in water before re-wearing or discarding.
• Immediately report leaks to your supervisor, warn people in the area, and move to a safe location, if necessary.